| Back to logs list
141806 2010 年 04 月 26 日 11:10 Reading (loading. ..) Comments (0) Category: Personal Diary
Tiggo common problems and treatment methods
1, Description of the problem: a sudden turn off the vehicle in motion, can not be started or the vehicle difficult to start the morning, the problem is caused by pump failure that hydraulic pressure relief problems: the problem mainly by the Pump The three causes
? pump in the course of the fuel tank cap and bellows bellows wear the interference caused rupture of oil spills.
tee at the oil pump assembly problems caused gasoline leak at high pressure can not build hydraulic ?
? oil pump motor mouth of the bellows assembly problems caused gas leak at high pressure can not be established The problem for the fuel pump hydraulic
, services, technology department organization number in 5.1 volume service station carried out the nature of the change, see specific after-sales technical documents SHJS05-10. However, reflecting the replacement part of the service station or individual vehicles are extremely fuel pump problem. In this regard, the analysis of our department and related departments for the production of this issue that the manufacturers of products not lead to consistency control, the other by the manufacturers at the tee on the pump assembly to re-design to solve the problem of pump oil.
switch off No.: 20 August 2005 production vehicles are the latest improvements have been the new state fuel pump.
approach: As the previous batch has already been replaced, your service station problem occurs only on the replacement of vehicles, not to the large quantities of replacement parts at the same time the company has asked the service station pump to return the old state companies Now there is no ordering of such a pump spare parts, please do not then the old service station pump for loading the state. Pump part number T11-1106610AB. Specific replacement of the part and claims operation mode, see
2, description of the problem: the length of the tire nut has two problems, the user found in the replacement tire tires used on the screw bolt length is different. Fault Description: The company's first production of vehicles (about 50 units), tire Lo Lo take as long to take, and later optimized to improve the short-Lo switch started to take
number: After statistical use long nut production of vehicles only the first 50 vehicles.
approach: If a user dispute, please order a short nut service station (now used in both the short nut) treatment. Part number: T11-3100111
3, Problem Description: Service station and customers reflect the accelerator pedal Tiggo weight, feel the engine speed slow phenomenon.
failure Note: for customers reflect the problem, the company conducted a study to take the following improved method
transfer efficiency due to the low throttle cable gas pedal weight; ?
partial throttle pedal lever ratio large, the throttle pedal lever ratio 0.8-0.93; ?
switch off No.: None
approach: on this issue reflect the client, please replace the improved throttle cable (up to 80% transfer efficiency ), please do not make large-volume service stations full replacement service station at the same time please note that when doing the deal with only the need to replace the cable, but do not replace the accelerator pedal, gas pedal because of the new car could not be installed to the old body, because fixation of the accelerator pedal position has changed. Throttle cable part number: T11-1108210.
4, Problem Description: drops of water inside the right front headlight.
Fault Description: Tiggo headlights for water problems, analysis that is because the rubber seals and wiring harness is not waterproof Mifengbuyan cause, the company has added water to this issue of the headlights and wiring harness plug seal waterproof plug used to switch off the technology to improve
No.: May 20,
coach handbags, 2005 were added after the production of car headlights and wiring harness water seal plug waterproof plug.
approach: for according to the standard headlights to determine whether the water after the water is recognized as the vehicle, replace the waterproof seal has been used with the plus headlights, wiring harness processing please use waterproof glue, for large Light water service stations claim, please carefully handled to avoid errors compensation. Headlight part number: T11-3772020.
5, Problem Description: Some of the feedback part of service stations in the course of the vehicle's sunroof sunroof does not automatically return to places that feature anti-pinch function and in the process of moving can not be opened.
failure Description: The main problem caused by the following non-
? sunroof anti-trap function and to use a great relationship, key to press to open the skylight skylights to reach the final end, this time If you press the close button, sunroof will automatically closed, if the time block glass window, with the micro-power, sunroof will automatically return to the back, in the process of self-closing sunroof Do not touch the switch,
Too much like the feeling of the wedding was - Qzo, otherwise the roof will go into manual mode; in the skylights automatically open or closed, touch switch, sunroof will enter manual mode,
Two days of selling virginity girls sold themselve, the process is not anti-trap function; the key off, do not remove the key when the roof is not enough to turn off automatically
, and only pull out the key, the sunroof to be able to automatically shut down.
? some of the vehicles in the moving process, when the speed exceeds 20km / h, the roof can not open the problems due to the module's internal procedures skylights caused
? pull off some of the vehicles in the key, the roof can not automatically shut down, the main cause is due to travel after ignition switch malfunction caused the limit switch is similar to the role of B11.
? self-learning no sunroof, press and hold until the sunroof fully open the key on, then press the Close button to completely shut down to hold the sunroof tilt sunroof button or press and hold for 15 seconds or more can also be skylight No switch off from learning
: May 31, 2005 cars were produced after the new state sunroof modules, to improve initial VIN code 5D047751
approach:
? skylight above the third module for failures, replace the new state of the sunroof module solutions, is the supply of spare parts for the new state of all modules
? points for its failure caused by the normal method of your circuit inspection,
coach bags, maintenance, and is due for customers use the feature skylights unclear questions, please explain to customers. Skylight module part number: T11-5703130. Replacement of roof modules, please fill in the after-sale management system, Fault Description: The analysis of the rubber seal that seals the sensor and the ring size of poor performance caused the seal of the material has been improved, and control the size of the ring to switch off
No.: None
approach: The oil spill occurred the vehicle odometer sensor, is replaced by a unified production of sensors Shanghai Pu students, part number: B11-3802020CA.
7, Problem Description: hot cars idling abnormal noise under the gearbox, clutch abnormal sound disappeared. Fault Description: The analysis that is due to the quality of Mitsubishi clutch, the clutch has been improved damping torque
Twist switch off No.: None
approach: for if the vehicle is loaded 2.0L's Mitsubishi hot car engine idling occurs abnormal noise under the gearbox, replace the 2.4L Mitsubishi engine Mitsubishi used on the clutch friction plate, spare part number: 2.4L clutch part number: MR534354 (clutch housing assembly), MN132443 (driven plate). If the vehicle is loaded 2.4L Mitsubishi engine idling hot car appeared abnormal noise under the gearbox. Please replace the Valeo clutch friction plate, part number: T11-1601030BA (driven plate), T11- 1601020BA (clutch housing assembly).
8, Problem Description: service stations reflect the gearbox oil can not be driving, check that the gearbox housing to be broken.
Fault Description: the dismantling of the gearbox fault found, the transmission planetary gear housing shaft fracture caused the problem to be broken by the analysis that is not caused by planetary gear shaft strength, and ultimately recognized as part of the planetary axis The phosphate treatment is not entirely caused by the planet axis is enhanced treatment (phosphate, shot peening, etc.), the problem has been basically solved.
switch off No.: No. in the gearbox are improved after MH5C00361 off pieces.
approach: break the problem appears gearbox housing, replace the gearbox assembly processing, do not number in the gearbox and replace all prior to transmission.
9, Problem Description: Some service stations reflect the very small portion of the car engine installed 2.0, jitter in the car idling serious need to increase the throttle or easy off heat. Fault Description: The cause of the problem for the pre-production problem with the engine ECU,
switch off No.: 8 May 2005 were produced after the new state of the ECU.
approach: For this problem, replace the existing production ECU, please replace the ECU before standing service to confirm whether there are other EFI system failure, has been to avoid the McDonald criteria.
10, Problem Description: Service station reflects the central power steering oil tank.
Fault Description: The confirmation of troubleshooting this problem for the power steering tank lid not lead to oil leakage due to sealing are improved, increase in the cap seal treatment.
switch off No.: June 20, 2005 the new state after the production of both pieces.
approach: For the lid at the oil spill occurred steering vehicles, service stations, please replace the power steering tank lid assembly.
11, Problem Description: differential oil seal leak.
Fault Description:
? Tiggo currently on the market two different forms of vehicles equipped with the right shaft, a drive shaft to the right is a whole long drive shaft, one consisting of two short composed of the right shaft for the vehicle drive shaft
? right coat for a long car drive shaft, differential oil seal leakage problem occurs is due to the right shaft is too long, resulting in oil seal Shouli Bu were caused by seal leakage.
? coat for the vehicle's drive shaft composed of two short right shaft of the car, analysts believe that with the axle shaft oil seal at the gap is too large chamfer lead, the lead angle is improved by 1 * 30 .
switch off No.: 20 August 2005 the new state after the production of both pieces.
approach:
? coat for the vehicle right for the long drive shaft of the car, if there is oil leakage problem, the right length shaft replacement on the grounds composed of two short right drive shaft axis, spare parts ordered from the new state of the spare parts that includes two half axle supported between the three bolts, parts are: Q184C1075, Q184C1060 (installed in the bracket following two bolts) and Q146C1055 (mounted on top of a bracket bolts, the need to support a fixed intake manifold removed a bolt, with the intake manifold bolts and axle support bracket fixed to the cylinder with the above).
coat for the vehicle drive shaft for the two short car drive shaft composed of the right, if there is oil leakage problem, replace the * near the short side axle differential, part number: T11-2203020BC. ?
? Please note that when you replace the differential oil seal installation method.
the right replacement drive shaft assembly, the minor axis of after-sale management system, please fill in the minor axis of the claim work-station: 88 88 40 08 ?
12, Problem Description: Vehicle driving wandering, after several adjustments were invalid
failure Description: The problem caused by two reasons, br> service stations use to adjust the wheel alignment parameters ?
not as long as the right drive shaft drive shaft caused ?
switch off No.: None
approach:
? For there wandering Please click the conventional method of vehicle inspection, and click the following data to adjust front wheel alignment
toe 0 '± 5' front wheel camber -0.85 ° ± 1 °
kingpin inclination of 11 ° 30 '± 45' kingpin inclination 2 ° 50 '± 45'
rear toe 18 '± 30' rear wheel camber -54 '± 30'
? invalid number for the above adjustments vehicle, set the right length shaft to replace the drive axle of two short and then the wheel alignment adjustment.
13, Problem Description: service stations reflect the part of the vehicle fuel tank vent pipe from the tank fill up after a spill at the phenomenon.
Fault Description: After analysis of that part of the fuel tank in the production process, process instability, air vents at the ring Mifengbuyan, Note: the location of the fuel tank vent pipe next to the main pump, in the main, the Deputy of the pump Switching off between
No.: None
approach: the problem for the oil tank cars there, please replace the service station tank to give treatment. When replacing the fuel tank assembly in the after-sale management system fill in the headlight adjustment, the right equipment for the electric headlight adjustment
Fault Description: This problem caused the assembly workshop
to switch off the error number: number and 5.24 3.28 days in the production of vehicles that may exist between this problem.
approach: service station numbers in the 3.28 and 5.24 at the vehicle that may exist between the production of this issue to check, if that side of the ESC installed headlights, side mounted headlight adjustment for the hand, if they find you to replace all the power transfer headlights, installed on both sides if they are hand-adjusted headlights, please replace all the electric headlight adjustment. Please replace the headlights in the after-sale management system, please fill out the 40 11
15, Problem Description: Service station opened with the remote locking is reflected in the existence of abnormal sound when the fault. Fault Description: this analysis that the electric control part of the meshing gears and rack space is too large,
Palmistry secrets you should know!, the transmission process is not smooth, leading to wear and tear caused by abnormal sound long-term use.
switch off number: 5D069569 previously produced in the presence of vehicles
approach this problem: the problem of vehicles there, please replace the new state of the closed service station assembly, provided spare parts are all for the improved pieces, each lock assembly part number: T11-6105040 (front right), T11-6105030 (left), T11-6205040 (right rear), T11-6205030 (left rear).
16, Problem Description: User reflected shock absorber oil, and sometimes produce abnormal sound when turning.
Fault Description: poor quality of the shock absorber shock absorber oil seal quality of performance does not meet the design requirements and other causes, there are seal and the use of imported parts are used to shift abnormal sound as the shock absorber bearing damage caused
switch off No.: VIN number code in 5D062012 car produced before the existence of this problem.
approach: the oil shock absorber and steering before the onset of abnormal sound when the vehicle, please replace the service station before the new state of shock absorber, part number: T11-2905010 (left), T11-2905020 ( right front). Please replace the front shock absorber in the after-sale management system, please fill out the : 88 88 40 13
17, Problem Description: After the shock absorber oil
users reflect the description of the problem: the poor quality of the shock absorber shock absorber oil seal of quality performance does not meet the design requirements other cause, there are seal and the use of imported parts are used.
switch off No.: VIN number code in 5D062012 car produced before the existence of this problem.
approach: the oil shock absorber and steering before the onset of abnormal sound when the vehicle, please replace the service station after the new state shock absorber, part number: T11-2915010. Please replace the rear shock absorber in the after-sale management system, please fill out the Hours after a single shock absorber claim disassembly station: 88884014, working two hours after the shock claim station: 88 88 40 15
18, Problem Description: service stations reflect the user Tires can not be replaced completely with a tire jack up top.
Fault Description: This problem is mainly due to both causes,
? Tiggo car jack for the car body drag arm support position supporting manner different from other vehicles at the bottom side of the skirt part, customers used to find the right support points are not the same time, a longer stroke shock absorber spring, causing the vehicle can not be raised, for which the Ministry has sent a service technician after-sale technical documents SHJS-05-11 number, replace the tire jack on the T11 Help
To further enhance the convenience of operation, the relevant departments to improve,
coach sunglasses outlet, now dragging into the support arm support boss, while deepening the depth of the groove jack. ?
switch off No.: August 30 towed vehicles produced after the support arm to support
boss approach: the problem of dealing with your customer service stations to the correct guiding the use of replacement tires made jack method, if there is a strong replacement customers complain about the state of the drag arm assembly,
coach sneakers, service station does not allow for batch replacement, the replacement must be in the form of information feedback report approved by the company.
19, Problem Description: clips easily inside the front door off the problem, leading to loosening of the former gate guard, fixed bad.
Fault Description: service stations reflect the right front door of a clamp inside a small, analysis is Zi Mukou size too small, not caused by the assembly in place.
switch off No.: August 23, 2005 cars were produced after the state installed a new clamp.
approach: snap off the vehicle for there, please replace the service station has increased the size of the buckle, to order your service station, part number: T11-6102421.
20, Problem Description: Service station reflects the loosening of the rear bumper of vehicles have led to water leakage inside the trunk.
failure Description: The analysis that caused the bumper clamp diameter is too small, has been improved to increase the clamp diameter.
switch off No.: VIN Code prior to the production of cars in 5D107747 possible
approach this problem: Replace the improved clamp solution. Part Number: T11-2804331 (the front of the rear bumper ends snap), T11-2804141 (rear bumper snaps), T11-2804341 (Central snap the rear bumper ends).
21, Problem Description: service stations reflect the oil filter with oil leakage.
Fault Description: manufacturer feedback, early production of the engine oil filter and engine combination of surface at a processing glitch, the pipeline processing at the angle (lead angle) is not processed, leading to cut through the seal to leak.
switch off No.: None
approach: the engine oil filter and engine combination in the face of the grinding burr burr
22,
coach purses, Problem Description: Some users complain that the vehicle noise, the whole the problem of bad car noise:
Fault Description: After analysis that: the former warehouse adverse effect of noise is the main reason for the new state by replacing the pads and other parts of the noise reduction of noise, the specific parts list, see the back of the NVH and LOTUS project improvement.
switch off No.: 20 August 2005 after the vehicles have improved results reflect the NVH.
approach: too much trouble to replace the insulator, the parts need to be demolished will be more on the technical requirements of high service station, for those in need of serious customer complaints to improve vehicle NVH and LOTUS, please stand dealing service special report before the form has been submitted to the Department of Technology Services, through the service agreement of Technology before replacement, or no claims.
23, Problem Description: service station, there are drops of water reflecting the front fog lamps and into the ash.
failure Description: The analysis that is caused by bad fog sealing, improved put a diaphragm in the air vent in the pipe blocks at Jiahai cotton dust.
switch off No.: VIN Code prior to the production of cars in 5D107747 possible approach to this problem
: For there before the onset of fog into water droplets or dust in the vehicle, replace the new state of the fog lights, part number for the T11-3732010 (left), T11-37320209 (front right), spare parts,
coach women shoes, company documents provided are improved parts.
24, Problem Description: Engine Rocker abnormal wear Description: the engine quality of the bearing arm, causing abnormal engine wear rocker, specific, see SHJS-05-10 pre-notification, pre- has organized special technical improvements
switch off No.: need to deal with the various service stations for vehicles, see SHJS-05-10 pre-notification
approach: maintenance and processing methods, see SHJS-05-10 pre-notification, Improvement of the issue now has been basically completed, a Swiss non-permission of the service stations selling tiger, which can not check processing, pre-requirements for the handling of the issue sold by the authority has Tiggo service stations to deal with the specific replacement parts operation and claims methods, see
25, description of the problem: transmission failure can not Guadang Note: Due to Tiggo shift gearbox used QR523 pins means excessive interference, leading to some of the vehicles of the press-fit pins are not in place , in the course of shedding can lead to hanging files, pre-technological improvements have organized special events.
switch off No.: need to deal with the various service stations for vehicles, see SHJS-05-10 pre-notification.
approach: maintenance and claims processing methods, see SHJS-05-10 pre-notification, the current improvement of the problem has been basically completed, a Swiss non-permission of the service stations selling tiger, which can not check processing, due to pre- requires the handling of the issue sold by the authority has Tiggo responsible for service stations, the replacement of parts specific way of operating and claims, see
26, description of the problem: cracking the engine belt tensioner, resulting in no power steering failure Description: The tension wheel design structure and material causes, pre-technological improvements have organized special events to switch off No.
: See the vehicles need to be addressed SHJS-05-12 pre-notification.
approach: maintenance and claims processing methods, see SHJS-05-12 pre-notification, the new state of no avail to replace the vehicle replacement parts. Specific replacement of the part and claims operation mode, see
27, Problem Description: Some customers reflect the linked file, the stalls are not clear
description of the problem: After the analysis of fault discovery parts, the transmission shift cable caused by low efficiency, change the shift cable has been designed to optimize the number
switch off: No
approach: the problem is optimization project, only to hang files for customers reflect the vehicle stalls deal are not clear, please replace the gear standing service Arm, part number: Please replace the service stand trial before the actual customer vehicles have confirmed the existence of the fault, do not produce false positives, and if changes need to replace parts service station service system to upload quality information through the feedback reports for approval and then to give customers change, the unauthorized change, the company will give exclusions
label automotive modules clutch ring gear
Missed all together - Qzone log
Linear Mode
