| Back to logs list
22129057 2008 年 04 月 10 日 13:28 Reading (loading. ..) Comments (0) Category: IT Technical
c , memory and hard disk
[system environment:] win XP SP2 + Jinshan +~~~ ! ! ! !
[basic configuration:] Celeron 1300 + GF 400 + Maxtor 40G, Memory 128M! ! Assembly machine! !
[failure description:] add memory boot no signal! !
[solution:]
1,
mbt anti shoe, initially suspected graphics card problem, examination was normal, the display is still no signal! !
2, other parts by the examination was normal! !
3, failure on the lock to the memory!
4, remove the memory, and then plug! Start a little signal, but disappeared immediately! !
insert a memory alone can sometimes be normal start!
appears to be memory slot problem!
had my friends do not know since recruited a DDR memory that is inserted once, can not boot to see taken out, and said how to plug it so hard! I faint! ! ! ! !
DDR and SDRAM, The difference is that a two-gap, a gap is only one! ! Plug lead to deformation of the hard
motherboard, memory, after the plug is not in place, loose, so when you plug in SDRAM, sometimes no signal situation! !
the cooperation of friends, the two SDRAM memory seated, place cards! !
restart, everything back to normal!
the failure of which, his friend had used the memory board does not support plug off, leading to deformation of the motherboard. Even then insert the correct memory,
mbt lami, sometimes loose! ! No signal power will naturally arise the phenomenon! !
God, he actually be able to plug in! !
[failure description] to upgrade the computer memory slot on the motherboard into the vacant memory, start the computer in the system properties not found to increase memory capacity.
[solution] to restart the computer, enter the cmos, will be transferred to save the default settings, the computer starts troubleshooting.
[system environment:] winxp
[failure description:] memory corruption causes the system registry errors
often reported such a failure of the more common, the performance of the system to be able to start normally,
mbt chapa, but when entering the desktop will be prompted to read the registry errors, you need to restart your computer to fix the error, but after start the computer again, still the same failure.
[Solution:] We can enter Safe Mode, run the typing If the troubleshooting, indicating that the problem really is caused by the registry errors; If the problem still exists, basically you can conclude that the machine memory problems, then need to use the replacement method, put on a good memory performance test whether there is The same failure.
Problem Description: Amy is a company's computer maintenance personnel, office machines flying to the moon for the Lenovo 2000 models, 13G hard drive, as long the computer system and data is not maintained, the system up and running slower than the , the C disk copy of important data on the D drive, then run the system recovery software, Lenovo will be hidden partition in the Windows98SE system to the C drive. Less than 10 minutes to restore is completed,
mbt uk, restart again, the normal into the Windows98 system. But into the system, found that the extended partition with PM by a large number of missing data in the extended partition, what to do? Wang embarrassing situation ... ...
Solution: First check Lenovo machines random data, a description that read, destroyed when the original hard disk partition table, is there any way to solve the problem? Or enter boot into MSDos PM, out of a primary partition and one extended partition is no other partition information, then think of the software Diskman, enter MSDos, run Diskman, the first warning that the partition table is incorrect, Diskman although still recognize the hard drive into two partition, but it also re-test the function of the partition table. Re-test a fully automated and interactive partition table in two ways, choose the latter, Diskman cylinder testing began by pre-existing hard disk partition table. After a very long time, the original association of three partitions, including hidden system recovery software, backup disks are detected out to keep geographical format, everything is normal.
Comments: User application or in the user partition on the hard disk drive partition table off will result in an error, encounter such problems do not worry, to analyze the problem, see the relevant information, such as software and The information came with your computer, using the relevant software or tools to solve, if the hard drive works, related software applications or tools are not very understanding, we must find the relevant information, or to the person asking.
Note: Diskman hard disk partition table maintenance software, run on MSDOS environment, the use of the whole Chinese graphical interface, without any Chinese system support. In the form of a chart reveals the detailed structure of the partition table to support the mouse, support large hard drives and more than 8G UNIX, NTFS partitions and other formats.
[Problem Description:] Sky II 5311 models of a user, the user of the software reflects the random NTI CD-Maker Plus FileCD tool in the time format rewritable discs (BenQ CD-RW), progress rapidly to 100%, but did not finish formatting tips, forced to close the dialog box can not be closed. Finally, only the end of such a task. With NTI CD-Maker Plus recording hard drive, burn to display the progress of the burning process, and prompt after burning, the burned CD into the drive, prompt does not recognize the disc.
[solution:] first consideration is the NTI CD-Maker software in the plug-in FileCD problem, upgrade NTI CD-Maker software to V5.08, V5.13, failed to resolve the phenomenon is still to upgrade to V5.15 , look FileCD version and the user version of the original machine FileCD as follow-up for the 2.0.10 version does not feature in the rewritable discs have been improved. Consider using other burning software, use NERO to test (version V5.5.9.0), using the software to perform a quick erase and then burn the disc, still the phenomenon of occurrence of the above. However, the use of SONY CD-RW disc does not have this problem.
Comments: rewritable disc burners and burning software and have a great relationship, your engineers can solve the problem consider the problem from several angles.
[Problem Description:] A user drives out of warranty,
mbt shoes sale, customers purchase their own drive, according to the user, said buying in the market when the test drive, CD-ROM without any problems, test data such as disc and VCD discs can be properly read out, However,
mbt trainers, the installation CD-ROM drive home after the boot into the system, all the disc into the CD-ROM drive letter in the display on the CD only kind of mark. The user back to the place of purchase to the test machine will be installed on the drive, the problem is complex.
Solution: After checking found that drive the data interface on a data line bending, resulting in the drive data can not be recognized properly.
Linear Mode
